How Bathtub Refinishing Works: The Complete Step-by-Step Process
This guide from Unique Refinishers walks you through exactly what happens during a professional bathtub refinishing job—so you know what to expect and why each step matters.
Why the Process Matters
Professional refinishers follow a systematic approach that includes deep cleaning, chip repair, surface etching, bonding primers, and multiple thin coats of high-solids acrylic-urethane or epoxy coating. Skipping any of these steps—or using inferior materials—compromises adhesion and drastically shortens the finish’s lifespan.
Step 1: Site Protection (15–20 minutes)
Before any work begins, the technician protects your bathroom by covering floors, walls, fixtures, and adjacent surfaces with plastic sheeting and drop cloths. This prevents overspray, dust, and debris from damaging your tile, vanity, or flooring.
Step 2: Hardware Removal (10–15 minutes)
The drain cover, overflow plate, faucet handles, and spout are removed to expose the entire tub surface and prevent coating buildup on hardware. Removing hardware also allows the finish to wrap cleanly around drain and overflow edges, creating a watertight seal.
Step 3: Strip Old Caulk (10–20 minutes)
All existing caulk and sealant around the tub perimeter is cut away and removed. Old caulk traps moisture and prevents new coating from bonding properly at the edges. Fresh caulk will be applied after refinishing to keep water out of joints.
Step 4: Deep Cleaning (15–25 minutes)
The tub is scrubbed with industrial-strength degreasers and cleaners to remove soap scum, body oils, mineral deposits, and cleaning product residue. This step is critical—any contamination left on the surface will block adhesion and cause premature peeling. The tub is rinsed multiple times until water runs clear.
Step 5: Chip and Crack Repair (15–30 minutes)
Visible chips, scratches, and small cracks are filled with a two-part epoxy filler or tub repair compound. Rust spots are treated and neutralized before filling. Once the filler cures, it's sanded flush with the surrounding surface so no imperfections show through the new finish.
Step 6: Surface Etching (20–30 minutes)
The entire tub surface is chemically etched with an acid solution or mechanically abraded with 400–600 grit wet/dry sandpaper. This creates a microscopic "tooth" or surface profile that allows the new coating to mechanically bond to the old substrate. Without proper etching, the finish will sit on top of the surface rather than adhering to it.
Step 7: Drying (10–15 minutes)
All moisture is removed from the tub surface using heat guns, blowers, or lint-free cloths. Even trace moisture trapped under the coating will cause bubbling, blushing, or adhesion failure.
Step 8: Masking (15–20 minutes)
Tile, drain openings, faucets, and surrounding surfaces are carefully masked off with painter's tape and plastic. This ensures clean edges and prevents overspray on areas that shouldn't be coated.
Step 9: Priming and Coating (45–75 minutes)
A bonding primer or adhesion promoter is applied first to create a chemical link between the old surface and new coating. Then, 2–3 thin, even coats of high-solids acrylic-urethane or epoxy topcoat are spray-applied using an HVLP (high-volume, low-pressure) spray gun. Multiple thin coats prevent drips, runs, and uneven coverage while building a durable, glossy finish. Each coat is allowed to flash-dry for 15–30 minutes before the next is applied.
After the final coat, the tub is left undisturbed to cure. Full chemical resistance and maximum hardness develop over 7–14 days, though normal bathing can resume after the initial cure window.
- Bathroom access: You can use the sink and toilet immediately; only the tub is off-limits
- Odor: Professional coatings are low-odor, but ventilation is recommended during application
- Final steps: After curing, masking is removed, hardware is reinstalled, and new caulk is applied around the perimeter
How to Prepare for Bathtub Refinishing
To ensure the best results, homeowners and property managers should:horow+1
- Remove all personal items from the tub area (shampoo, razors, bath mats, etc.)
- Clear the bathroom floor and vanity top for technician access
- Ensure adequate ventilation (open windows or run exhaust fan)
- Keep pets and children away from the work area during application
Why Choose Unique Refinishers?
Ready to see the process in action?
